开关柜厂家
贵州开关柜浅谈对柜体导线、母线的细致检查
您的当前位置: 贵阳开关柜 >> 新闻动态 >> 行业新闻

贵州开关柜浅谈对柜体导线、母线的细致检查

发布日期:2018-01-19 作者:贵州开关柜 点击:

贵州开关柜浅谈对柜体导线、母线的细致检查

The careful examination of the wire and busbar of the cabinet body in Guizhou switch cabinet

贵州开关柜

在开关柜产品出厂之前,开关柜生产厂家都会对其进行全面的检查,其中较为重要的检查内容就是针对内部导线的制作安装以及母线的安装。若是这两部分有不不满足要求的现象存在的话,

Switchgear manufacturers will conduct a comprehensive inspection of the switchgear products before they leave the factory. The most important content is the installation and installation of the internal conductor and the installation of the busbar. If there is a phenomenon that the two parts do not fail to meet the requirements,


整个开关柜的正常运行都会受到干扰。

The normal operation of the whole switchgear will be disturbed.

1、开关柜生产厂家对柜体内部导线的检查

1. The inspection of the wire in the cabinet by the manufacturer of the switchgear


贵州开关柜提醒首先是关于导线选用的型号和规格,务必要与需求相符;同时检查开关柜导线两端是否标记有相序,保证其连接正确。

The switch cabinet in Guizhou reminds us first of all about the type and specification of wire selection. It is necessary to conform to requirements. Meanwhile, check whether there are phase sequence on both ends of the switch cabinet, so as to ensure that the connection is correct.

其次是关于导线的长度,不能过长也不能过短;并且不适合进行多束捆扎,以免使导线受损。

The second is the length of the wire, which can not be too long or too short; and it is not suitable for multi bundle binding so as to avoid the damage of the wire.

另外关注到的还有导线的接头、;连接螺栓等等,需要正确合理的选用规格,并在特定的情况下做好防护处理。当导线遇到发热元件或主母线的时候,要把持一定的间距不能过于靠紧。

In addition, there are also the connection of the wire, the connection bolt and so on, which need correct and reasonable selection of specifications, and do a good job in a specific case. When encountered wire heating element or main busbar, should hold a certain distance too close.


2、开关柜生产厂家对柜体内母线的检查

2. The inspection of the busbar in the cabinet by the manufacturer of the switchgear

开关柜中母线的安装应该参照相应的图纸进行,并且要留出一定的空间便于它的进出;就母线自身而言,应保持表面平整、无裂纹、无毛刺等。

The installation of bus bar in switchgear should be carried out according to the corresponding drawings, and there must be some space for its entry and exit. For the busbar itself, the surface should be kept smooth, no cracks and no burrs.

要与母线连接的各类紧固件要选择规格适中的,且紧固螺栓力矩值也要符合要求,在其紧固之后还要标记出标记线。

All kinds of fasteners to be connected to the bus bar should be selected with moderate specifications, and the tightening bolt torque values should also meet the requirements. After marking the fasteners, marking lines should be marked.


本文网址:http://www.paschernikeairmaxtailwind.pw/news/219.html

相关标签:贵州开关柜

最近浏览:

2017年六开彩开奖结果